Overview of all web interface settings EMS-ESP V2

The Gateway models Premium, Premium II, Standard and Regular are based on the EMS-ESP V2 firmware.

Note

The EMS-ESP firmware V2 project has now been archived. It is recommended to upgrade to an ESP32 chip to make use of the much improved EMS-ESP32 V3 firmware. See this page for more information.

There’s a whole range of other settings you can make from within the web interface. Most speak for themselves. Below an overview of all pages. With each new firmware version features are added and sometimes removed. The pages below are based on V2 firmware. If you have a Gateway S32 or E32 look HERE for the V3 firmware.

Dashboard

The dashboard page provides a more detailed overview of the status of the Gateway.

Devices and Sensors

The Devices and Sensors tab gives you an overview of all devices found on the EMS bus. If you are missing a device, press the ‘Scan Devices’ button.

If you connected DS18B20 sensors these are listed as well.

Web interface Devices and Sensors tab

EMS Status

The EMS Status tab gives you information if the bus is connected correctly.

Web interface EMS Status tab

EMS-ESP Help

This page provides links to the help function.

Web interface EMS-ESP Help tab

Settings

On the EMS-ESP settings page you can change the Tx mode and change the Bus ID of the Gateway. Also you can turn on the Shower Timer and Shower Alert features which give a notification of shower duration in Home Assistant and a cold burst of water after a few minutes.

Web interface EMS-ESP settings

Note

Setting TX delay for Buderus Web KM200/KM100/KM50/boilers with ethernet: If you have a Bosch/Buderus Web gateway module like the KM200, KM100, KM50 or your boiler has one built in, you need to go to Settings and then set ‘TX delayed start’ to 60 seconds.

WiFi Connection

WiFi Status

The WiFi Status tab gives you all the network status and parameters.

Web interface WiFi status tab

Scan Networks

Scan networks provides the option to scan and select a specific Wi-Fi network.

Web interface WiFi Scan networks tab

WiFi Settings

The WiFi Settings tab gives you the network teh Gateway is currently connected to. You can also set the Wi-Fi password, network Hostname and set a static IP address.

Web interface WiFi Settings tab

Access Point

Access Point Status

The Access Point Status tab gives you the status of the internal access point of the Gateway.

Web interface Access point Status tab

Access Point Settings

You can set the AP Wi-Fi name and password and other network settings.

Web interface Access point Settings tab

Network Time

NTP Status

The NTP Status tab gives you information about the network time status.

Web interface NTP Status tab

NTP Settings

Web interface NTP Status tab

MQTT

MQTT Status

The MQTT Status tab gives you information about the MQTT connection to the broker.

Web interface MQTT Status tab

MQTT Settings

Here you can set a lot of MQTT related parameters.

Web interface MQTT Settings tab

Security

Manage users

Add or remove users of EMS-ESP.

Web interface manage users tab

Security Settings

Web interface security settings tab

System

System Status

See the status of a lot of ESP parameters. You can also reboot the Gateway here or perform a factory reset.

Web interface system status tab Web interface factory reset

OTA Settings

Here you can set OTA (Over the Air) firmare upgrade parameters. With this function you can upload new firmware via WiFi directly from Platform IO to the ESP module.

Web interface OTA settings tab

Update firmware

On this page you can update the firmware of the Gateway. First you can download the latest stable version and then upload the bin file or another bin file to the Gateway.

Warning

The Gateways models Premium (II), Standard and Regular are based on the ESP8266. Always chose the ESP8266 bin file!. If you upload the ESP32 bin file you will brick the Gateway and you need to use Platform I/O or the ESP loader to install the correct firmware again.

If your Gateway works fine and there are no significant new features, its not recommended to update the firmware just for the sake of updating. Some firmware versions are not stable and can give stability issues.

Web interface firmware update menu